567 lines
20 KiB
C
567 lines
20 KiB
C
|
/* This source file is part of the ATMEL AVR-UC3-SoftwareFramework-1.7.0 Release */
|
||
|
|
|
||
|
|
/*This file has been prepared for Doxygen automatic documentation generation.*/
|
||
|
|
/*! \file *********************************************************************
|
||
|
|
*
|
||
|
|
* \brief High-level library abstracting features such as oscillators/pll/dfll
|
||
|
|
* configuration, clock configuration, System-sensible parameters
|
||
|
|
* configuration, buses clocks configuration, sleep mode, reset.
|
||
|
|
*
|
||
|
|
*
|
||
|
|
* - Compiler: IAR EWAVR32 and GNU GCC for AVR32
|
||
|
|
* - Supported devices: All AVR32 devices.
|
||
|
|
* - AppNote:
|
||
|
|
*
|
||
|
|
* \author Atmel Corporation: http://www.atmel.com \n
|
||
|
|
* Support and FAQ: http://support.atmel.no/
|
||
|
|
*
|
||
|
|
*****************************************************************************/
|
||
|
|
|
||
|
|
/* Copyright (c) 2009 Atmel Corporation. All rights reserved.
|
||
|
|
*
|
||
|
|
* Redistribution and use in source and binary forms, with or without
|
||
|
|
* modification, are permitted provided that the following conditions are met:
|
||
|
|
*
|
||
|
|
* 1. Redistributions of source code must retain the above copyright notice, this
|
||
|
|
* list of conditions and the following disclaimer.
|
||
|
|
*
|
||
|
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||
|
|
* this list of conditions and the following disclaimer in the documentation
|
||
|
|
* and/or other materials provided with the distribution.
|
||
|
|
*
|
||
|
|
* 3. The name of Atmel may not be used to endorse or promote products derived
|
||
|
|
* from this software without specific prior written permission.
|
||
|
|
*
|
||
|
|
* 4. This software may only be redistributed and used in connection with an Atmel
|
||
|
|
* AVR product.
|
||
|
|
*
|
||
|
|
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
|
||
|
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
||
|
|
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
|
||
|
|
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
|
||
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
||
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
||
|
|
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
|
||
|
|
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
||
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
|
||
|
|
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
#include "power_clocks_lib.h"
|
||
|
|
|
||
|
|
|
||
|
|
//! Device-specific data
|
||
|
|
#if UC3L
|
||
|
|
static long int pcl_configure_clocks_uc3l(pcl_freq_param_t *param); // FORWARD declaration
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#if UC3C
|
||
|
|
static long int pcl_configure_clocks_uc3c(pcl_freq_param_t *param); // FORWARD declaration
|
||
|
|
#endif
|
||
|
|
|
||
|
|
long int pcl_configure_clocks(pcl_freq_param_t *param)
|
||
|
|
{
|
||
|
|
#ifndef AVR32_PM_VERSION_RESETVALUE
|
||
|
|
// Implementation for UC3A, UC3A3, UC3B parts.
|
||
|
|
return(pm_configure_clocks(param));
|
||
|
|
#else
|
||
|
|
#ifdef AVR32_PM_410_H_INCLUDED
|
||
|
|
// Implementation for UC3C parts.
|
||
|
|
return(pcl_configure_clocks_uc3c(param));
|
||
|
|
#else
|
||
|
|
// Implementation for UC3L parts.
|
||
|
|
return(pcl_configure_clocks_uc3l(param));
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
//! Device-specific implementation
|
||
|
|
#if UC3L
|
||
|
|
// FORWARD declaration
|
||
|
|
static long int pcl_configure_synchronous_clocks( pm_clk_src_t main_clk_src,
|
||
|
|
unsigned long main_clock_freq_hz,
|
||
|
|
pcl_freq_param_t *param);
|
||
|
|
|
||
|
|
long int pcl_configure_clocks_rcsys(pcl_freq_param_t *param)
|
||
|
|
{
|
||
|
|
// Supported main clock sources: PCL_MC_RCSYS
|
||
|
|
|
||
|
|
// Supported synchronous clocks frequencies if RCSYS is the main clock source:
|
||
|
|
// 115200Hz, 57600Hz, 28800Hz, 14400Hz, 7200Hz, 3600Hz, 1800Hz, 900Hz, 450Hz.
|
||
|
|
|
||
|
|
// NOTE: by default, this implementation doesn't perform thorough checks on the
|
||
|
|
// input parameters. To enable the checks, define AVR32SFW_INPUT_CHECK.
|
||
|
|
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that fCPU >= fPBx
|
||
|
|
if((param->cpu_f < param->pba_f) || (param->cpu_f < param->pbb_f))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that the target frequencies are reachable.
|
||
|
|
if((param->cpu_f > SCIF_SLOWCLOCK_FREQ_HZ) || (param->pba_f > SCIF_SLOWCLOCK_FREQ_HZ)
|
||
|
|
|| (param->pbb_f > SCIF_SLOWCLOCK_FREQ_HZ))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
return(pcl_configure_synchronous_clocks(PM_CLK_SRC_SLOW, SCIF_SLOWCLOCK_FREQ_HZ, param));
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
long int pcl_configure_clocks_rc120m(pcl_freq_param_t *param)
|
||
|
|
{
|
||
|
|
// Supported main clock sources: PCL_MC_RC120M
|
||
|
|
|
||
|
|
// Supported synchronous clocks frequencies if RC120M is the main clock source:
|
||
|
|
// 30MHz, 15MHz, 7.5MHz, 3.75MHz, 1.875MHz, 937.5kHz, 468.75kHz.
|
||
|
|
|
||
|
|
// NOTE: by default, this implementation doesn't perform thorough checks on the
|
||
|
|
// input parameters. To enable the checks, define AVR32SFW_INPUT_CHECK.
|
||
|
|
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that fCPU >= fPBx
|
||
|
|
if((param->cpu_f < param->pba_f) || (param->cpu_f < param->pbb_f))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that the target frequencies are reachable.
|
||
|
|
if((param->cpu_f > SCIF_RC120M_FREQ_HZ) || (param->pba_f > SCIF_RC120M_FREQ_HZ)
|
||
|
|
|| (param->pbb_f > SCIF_RC120M_FREQ_HZ))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
// Start the 120MHz internal RCosc (RC120M) clock
|
||
|
|
scif_start_rc120M();
|
||
|
|
|
||
|
|
return(pcl_configure_synchronous_clocks(PM_CLK_SRC_RC120M, SCIF_RC120M_FREQ_HZ, param));
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
long int pcl_configure_clocks_osc0(pcl_freq_param_t *param)
|
||
|
|
{
|
||
|
|
// Supported main clock sources: PCL_MC_OSC0
|
||
|
|
|
||
|
|
// Supported synchronous clocks frequencies if OSC0 is the main clock source:
|
||
|
|
// (these obviously depend on the OSC0 frequency; we'll take 16MHz as an example)
|
||
|
|
// 16MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500kHz, 250kHz, 125kHz, 62.5kHz.
|
||
|
|
|
||
|
|
// NOTE: by default, this implementation doesn't perform thorough checks on the
|
||
|
|
// input parameters. To enable the checks, define AVR32SFW_INPUT_CHECK.
|
||
|
|
|
||
|
|
unsigned long main_clock_freq;
|
||
|
|
|
||
|
|
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that fCPU >= fPBx
|
||
|
|
if((param->cpu_f < param->pba_f) || (param->cpu_f < param->pbb_f))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
main_clock_freq = param->osc0_f;
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that the target frequencies are reachable.
|
||
|
|
if((param->cpu_f > main_clock_freq) || (param->pba_f > main_clock_freq)
|
||
|
|
|| (param->pbb_f > main_clock_freq))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
// Configure OSC0 in crystal mode, external crystal with a fcrystal Hz frequency.
|
||
|
|
scif_configure_osc_crystalmode(SCIF_OSC0, main_clock_freq);
|
||
|
|
// Enable the OSC0
|
||
|
|
scif_enable_osc(SCIF_OSC0, param->osc0_startup, true);
|
||
|
|
|
||
|
|
return(pcl_configure_synchronous_clocks(PM_CLK_SRC_OSC0, main_clock_freq, param));
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
long int pcl_configure_clocks_dfll0(pcl_freq_param_t *param)
|
||
|
|
{
|
||
|
|
// Supported main clock sources: PCL_MC_DFLL
|
||
|
|
|
||
|
|
// Supported synchronous clocks frequencies if DFLL is the main clock source:
|
||
|
|
// (these obviously depend on the DFLL target frequency; we'll take 100MHz as an example)
|
||
|
|
// 50MHz, 25MHz, 12.5MHz, 6.25MHz, 3.125MHz, 1562.5kHz, 781.25kHz, 390.625kHz.
|
||
|
|
|
||
|
|
// NOTE: by default, this implementation doesn't perform thorough checks on the
|
||
|
|
// input parameters. To enable the checks, define AVR32SFW_INPUT_CHECK.
|
||
|
|
|
||
|
|
unsigned long main_clock_freq;
|
||
|
|
scif_gclk_opt_t *pgc_dfllif_ref_opt;
|
||
|
|
|
||
|
|
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that fCPU >= fPBx
|
||
|
|
if((param->cpu_f < param->pba_f) || (param->cpu_f < param->pbb_f))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
main_clock_freq = param->dfll_f;
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that the target DFLL output frequency is in the correct range.
|
||
|
|
if((main_clock_freq > SCIF_DFLL_MAXFREQ_HZ) || (main_clock_freq < SCIF_DFLL_MINFREQ_HZ))
|
||
|
|
return(-1);
|
||
|
|
// Verify that the target frequencies are reachable.
|
||
|
|
if((param->cpu_f > main_clock_freq) || (param->pba_f > main_clock_freq)
|
||
|
|
|| (param->pbb_f > main_clock_freq))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
pgc_dfllif_ref_opt = (scif_gclk_opt_t *)param->pextra_params;
|
||
|
|
// Implementation note: this implementation configures the DFLL in closed-loop
|
||
|
|
// mode (because it gives the best accuracy) which enables the generic clock CLK_DFLLIF_REF
|
||
|
|
// as a reference (RCSYS being used as the generic clock source, undivided).
|
||
|
|
scif_dfll0_closedloop_configure_and_start(pgc_dfllif_ref_opt, main_clock_freq, TRUE);
|
||
|
|
|
||
|
|
return(pcl_configure_synchronous_clocks(PM_CLK_SRC_DFLL0, main_clock_freq, param));
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
static long int pcl_configure_clocks_uc3l(pcl_freq_param_t *param)
|
||
|
|
{
|
||
|
|
// Supported main clock sources: PCL_MC_RCSYS, PCL_MC_OSC0, PCL_MC_DFLL0, PCL_MC_RC120M
|
||
|
|
|
||
|
|
// Supported synchronous clocks frequencies if RCSYS is the main clock source:
|
||
|
|
// 115200Hz, 57600Hz, 28800Hz, 14400Hz, 7200Hz, 3600Hz, 1800Hz, 900Hz, 450Hz.
|
||
|
|
|
||
|
|
// Supported synchronous clocks frequencies if RC120M is the main clock source:
|
||
|
|
// 30MHz, 15MHz, 7.5MHz, 3.75MHz, 1.875MHz, 937.5kHz, 468.75kHz.
|
||
|
|
|
||
|
|
// Supported synchronous clocks frequencies if OSC0 is the main clock source:
|
||
|
|
// (these obviously depend on the OSC0 frequency; we'll take 16MHz as an example)
|
||
|
|
// 16MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500kHz, 250kHz, 125kHz, 62.5kHz.
|
||
|
|
|
||
|
|
// Supported synchronous clocks frequencies if DFLL is the main clock source:
|
||
|
|
// (these obviously depend on the DFLL target frequency; we'll take 100MHz as an example)
|
||
|
|
// 50MHz, 25MHz, 12.5MHz, 6.25MHz, 3.125MHz, 1562.5kHz, 781.25kHz, 390.625kHz.
|
||
|
|
|
||
|
|
// NOTE: by default, this implementation doesn't perform thorough checks on the
|
||
|
|
// input parameters. To enable the checks, define AVR32SFW_INPUT_CHECK.
|
||
|
|
|
||
|
|
|
||
|
|
#ifdef AVR32SFW_INPUT_CHECK
|
||
|
|
// Verify that fCPU >= fPBx
|
||
|
|
if((param->cpu_f < param->pba_f) || (param->cpu_f < param->pbb_f))
|
||
|
|
return(-1);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
if(PCL_MC_RCSYS == param->main_clk_src)
|
||
|
|
{
|
||
|
|
return(pcl_configure_clocks_rcsys(param));
|
||
|
|
}
|
||
|
|
else if(PCL_MC_RC120M == param->main_clk_src)
|
||
|
|
{
|
||
|
|
return(pcl_configure_clocks_rc120m(param));
|
||
|
|
}
|
||
|
|
else if(PCL_MC_OSC0 == param->main_clk_src)
|
||
|
|
{
|
||
|
|
return(pcl_configure_clocks_osc0(param));
|
||
|
|
}
|
||
|
|
else // PCL_MC_DFLL0 == param->main_clk_src
|
||
|
|
{
|
||
|
|
return(pcl_configure_clocks_dfll0(param));
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
static long int pcl_configure_synchronous_clocks(pm_clk_src_t main_clk_src, unsigned long main_clock_freq_hz, pcl_freq_param_t *param)
|
||
|
|
{
|
||
|
|
//#
|
||
|
|
//# Set the Synchronous clock division ratio for each clock domain
|
||
|
|
//#
|
||
|
|
pm_set_all_cksel(main_clock_freq_hz, param->cpu_f, param->pba_f, param->pbb_f);
|
||
|
|
|
||
|
|
//#
|
||
|
|
//# Set the Flash wait state and the speed read mode (depending on the target CPU frequency).
|
||
|
|
//#
|
||
|
|
#if UC3L
|
||
|
|
flashcdw_set_flash_waitstate_and_readmode(param->cpu_f);
|
||
|
|
#elif UC3C
|
||
|
|
flashc_set_flash_waitstate_and_readmode(param->cpu_f);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
|
||
|
|
//#
|
||
|
|
//# Switch the main clock source to the selected clock.
|
||
|
|
//#
|
||
|
|
pm_set_mclk_source(main_clk_src);
|
||
|
|
|
||
|
|
return PASS;
|
||
|
|
}
|
||
|
|
|
||
|
|
#endif // UC3L device-specific implementation
|
||
|
|
|
||
|
|
//! UC3C Device-specific implementation
|
||
|
|
#if UC3C
|
||
|
|
static long int pcl_configure_clocks_uc3c(pcl_freq_param_t *param)
|
||
|
|
{
|
||
|
|
#define PM_MAX_MUL ((1 << AVR32_SCIF_PLLMUL_SIZE) - 1)
|
||
|
|
#define AVR32_PM_PBA_MAX_FREQ 66000000
|
||
|
|
#define AVR32_PM_PLL_VCO_RANGE0_MAX_FREQ 240000000
|
||
|
|
#define AVR32_PM_PLL_VCO_RANGE0_MIN_FREQ 160000000
|
||
|
|
|
||
|
|
// Implementation for UC3C parts.
|
||
|
|
// Supported frequencies:
|
||
|
|
// Fosc0 mul div PLL div2_en cpu_f pba_f Comment
|
||
|
|
// 12 15 1 192 1 12 12
|
||
|
|
// 12 9 3 40 1 20 20 PLL out of spec
|
||
|
|
// 12 15 1 192 1 24 12
|
||
|
|
// 12 9 1 120 1 30 15
|
||
|
|
// 12 9 3 40 0 40 20 PLL out of spec
|
||
|
|
// 12 15 1 192 1 48 12
|
||
|
|
// 12 15 1 192 1 48 24
|
||
|
|
// 12 8 1 108 1 54 27
|
||
|
|
// 12 9 1 120 1 60 15
|
||
|
|
// 12 9 1 120 1 60 30
|
||
|
|
// 12 10 1 132 1 66 16.5
|
||
|
|
//
|
||
|
|
unsigned long in_cpu_f = param->cpu_f;
|
||
|
|
unsigned long in_osc0_f = param->osc0_f;
|
||
|
|
unsigned long mul, div, div2_en = 0, div2_cpu = 0, div2_pba = 0;
|
||
|
|
unsigned long pll_freq, rest;
|
||
|
|
Bool b_div2_pba, b_div2_cpu;
|
||
|
|
|
||
|
|
// Configure OSC0 in crystal mode, external crystal with a FOSC0 Hz frequency.
|
||
|
|
scif_configure_osc_crystalmode(SCIF_OSC0, in_osc0_f);
|
||
|
|
// Enable the OSC0
|
||
|
|
scif_enable_osc(SCIF_OSC0, param->osc0_startup, true);
|
||
|
|
// Set the main clock source as being OSC0.
|
||
|
|
pm_set_mclk_source(PM_CLK_SRC_OSC0);
|
||
|
|
|
||
|
|
// Start with CPU freq config
|
||
|
|
if (in_cpu_f == in_osc0_f)
|
||
|
|
{
|
||
|
|
param->cpu_f = in_osc0_f;
|
||
|
|
param->pba_f = in_osc0_f;
|
||
|
|
return PASS;
|
||
|
|
}
|
||
|
|
else if (in_cpu_f < in_osc0_f)
|
||
|
|
{
|
||
|
|
// TBD
|
||
|
|
}
|
||
|
|
|
||
|
|
rest = in_cpu_f % in_osc0_f;
|
||
|
|
|
||
|
|
for (div = 1; div < 32; div++)
|
||
|
|
{
|
||
|
|
if ((div * rest) % in_osc0_f == 0)
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
if (div == 32)
|
||
|
|
return FAIL;
|
||
|
|
|
||
|
|
mul = (in_cpu_f * div) / in_osc0_f;
|
||
|
|
|
||
|
|
if (mul > PM_MAX_MUL)
|
||
|
|
return FAIL;
|
||
|
|
|
||
|
|
// export 2power from PLL div to div2_cpu
|
||
|
|
while (!(div % 2))
|
||
|
|
{
|
||
|
|
div /= 2;
|
||
|
|
div2_cpu++;
|
||
|
|
}
|
||
|
|
|
||
|
|
// Here we know the mul and div parameter of the PLL config.
|
||
|
|
// . Check out if the PLL has a valid in_cpu_f.
|
||
|
|
// . Try to have for the PLL frequency (VCO output) the highest possible value
|
||
|
|
// to reduce jitter.
|
||
|
|
while (in_osc0_f * 2 * mul / div < AVR32_PM_PLL_VCO_RANGE0_MAX_FREQ)
|
||
|
|
{
|
||
|
|
if (2 * mul > PM_MAX_MUL)
|
||
|
|
break;
|
||
|
|
mul *= 2;
|
||
|
|
div2_cpu++;
|
||
|
|
}
|
||
|
|
|
||
|
|
if (div2_cpu != 0)
|
||
|
|
{
|
||
|
|
div2_cpu--;
|
||
|
|
div2_en = 1;
|
||
|
|
}
|
||
|
|
|
||
|
|
pll_freq = in_osc0_f * mul / (div * (1 << div2_en));
|
||
|
|
|
||
|
|
// Update real CPU Frequency
|
||
|
|
param->cpu_f = pll_freq / (1 << div2_cpu);
|
||
|
|
mul--;
|
||
|
|
|
||
|
|
scif_pll_opt_t opt;
|
||
|
|
|
||
|
|
opt.osc = SCIF_OSC0, // Sel Osc0 or Osc1
|
||
|
|
opt.lockcount = 16, // lockcount in main clock for the PLL wait lock
|
||
|
|
opt.div = div, // DIV=1 in the formula
|
||
|
|
opt.mul = mul, // MUL=7 in the formula
|
||
|
|
opt.pll_div2 = div2_en, // pll_div2 Divide the PLL output frequency by 2 (this settings does not change the FVCO value)
|
||
|
|
opt.pll_wbwdisable = 0, //pll_wbwdisable 1 Disable the Wide-Bandith Mode (Wide-Bandwith mode allow a faster startup time and out-of-lock time). 0 to enable the Wide-Bandith Mode.
|
||
|
|
opt.pll_freq = (pll_freq < AVR32_PM_PLL_VCO_RANGE0_MIN_FREQ) ? 1 : 0, // Set to 1 for VCO frequency range 80-180MHz, set to 0 for VCO frequency range 160-240Mhz.
|
||
|
|
|
||
|
|
|
||
|
|
scif_pll_setup(SCIF_PLL0, opt); // lockcount in main clock for the PLL wait lock
|
||
|
|
|
||
|
|
/* Enable PLL0 */
|
||
|
|
scif_pll_enable(SCIF_PLL0);
|
||
|
|
|
||
|
|
/* Wait for PLL0 locked */
|
||
|
|
scif_wait_for_pll_locked(SCIF_PLL0) ;
|
||
|
|
|
||
|
|
rest = pll_freq;
|
||
|
|
while (rest > AVR32_PM_PBA_MAX_FREQ ||
|
||
|
|
rest != param->pba_f)
|
||
|
|
{
|
||
|
|
div2_pba++;
|
||
|
|
rest = pll_freq / (1 << div2_pba);
|
||
|
|
if (rest < param->pba_f)
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
|
||
|
|
// Update real PBA Frequency
|
||
|
|
param->pba_f = pll_freq / (1 << div2_pba);
|
||
|
|
|
||
|
|
|
||
|
|
if (div2_cpu)
|
||
|
|
{
|
||
|
|
b_div2_cpu = TRUE;
|
||
|
|
div2_cpu--;
|
||
|
|
}
|
||
|
|
else
|
||
|
|
b_div2_cpu = FALSE;
|
||
|
|
|
||
|
|
if (div2_pba)
|
||
|
|
{
|
||
|
|
b_div2_pba = TRUE;
|
||
|
|
div2_pba--;
|
||
|
|
}
|
||
|
|
else
|
||
|
|
b_div2_pba = FALSE;
|
||
|
|
|
||
|
|
if (b_div2_cpu == TRUE )
|
||
|
|
{
|
||
|
|
pm_set_clk_domain_div(PM_CLK_DOMAIN_0, (pm_divratio_t) div2_cpu); // CPU
|
||
|
|
pm_set_clk_domain_div(PM_CLK_DOMAIN_1, (pm_divratio_t) div2_cpu); // HSB
|
||
|
|
pm_set_clk_domain_div(PM_CLK_DOMAIN_3, (pm_divratio_t) div2_cpu); // PBB
|
||
|
|
}
|
||
|
|
if (b_div2_pba == TRUE )
|
||
|
|
{
|
||
|
|
pm_set_clk_domain_div(PM_CLK_DOMAIN_2, (pm_divratio_t) div2_pba); // PBA
|
||
|
|
pm_set_clk_domain_div(PM_CLK_DOMAIN_4, (pm_divratio_t) div2_pba); // PBC
|
||
|
|
}
|
||
|
|
|
||
|
|
// Set Flashc Wait State
|
||
|
|
flashc_set_flash_waitstate_and_readmode(param->cpu_f);
|
||
|
|
|
||
|
|
// Set the main clock source as being PLL0.
|
||
|
|
pm_set_mclk_source(PM_CLK_SRC_PLL0);
|
||
|
|
|
||
|
|
return PASS;
|
||
|
|
}
|
||
|
|
#endif // UC3C device-specific implementation
|
||
|
|
|
||
|
|
long int pcl_switch_to_osc(pcl_osc_t osc, unsigned int fcrystal, unsigned int startup)
|
||
|
|
{
|
||
|
|
#ifndef AVR32_PM_VERSION_RESETVALUE
|
||
|
|
// Implementation for UC3A, UC3A3, UC3B parts.
|
||
|
|
if(PCL_OSC0 == osc)
|
||
|
|
{
|
||
|
|
// Configure OSC0 in crystal mode, external crystal with a FOSC0 Hz frequency,
|
||
|
|
// enable the OSC0, set the main clock source as being OSC0.
|
||
|
|
pm_switch_to_osc0(&AVR32_PM, fcrystal, startup);
|
||
|
|
}
|
||
|
|
else
|
||
|
|
{
|
||
|
|
return PCL_NOT_SUPPORTED;
|
||
|
|
}
|
||
|
|
#else
|
||
|
|
// Implementation for UC3C, UC3L parts.
|
||
|
|
#if AVR32_PM_VERSION_RESETVALUE < 0x400
|
||
|
|
return PCL_NOT_SUPPORTED;
|
||
|
|
#else
|
||
|
|
if(PCL_OSC0 == osc)
|
||
|
|
{
|
||
|
|
// Configure OSC0 in crystal mode, external crystal with a fcrystal Hz frequency.
|
||
|
|
scif_configure_osc_crystalmode(SCIF_OSC0, fcrystal);
|
||
|
|
// Enable the OSC0
|
||
|
|
scif_enable_osc(SCIF_OSC0, startup, true);
|
||
|
|
// Set the Flash wait state and the speed read mode (depending on the target CPU frequency).
|
||
|
|
#if UC3L
|
||
|
|
flashcdw_set_flash_waitstate_and_readmode(fcrystal);
|
||
|
|
#elif UC3C
|
||
|
|
flashc_set_flash_waitstate_and_readmode(fcrystal);
|
||
|
|
#endif
|
||
|
|
// Set the main clock source as being OSC0.
|
||
|
|
pm_set_mclk_source(PM_CLK_SRC_OSC0);
|
||
|
|
}
|
||
|
|
else
|
||
|
|
{
|
||
|
|
return PCL_NOT_SUPPORTED;
|
||
|
|
}
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
return PASS;
|
||
|
|
}
|
||
|
|
|
||
|
|
long int pcl_configure_usb_clock(void)
|
||
|
|
{
|
||
|
|
#ifndef AVR32_PM_VERSION_RESETVALUE
|
||
|
|
// Implementation for UC3A, UC3A3, UC3B parts.
|
||
|
|
pm_configure_usb_clock();
|
||
|
|
return PASS;
|
||
|
|
#else
|
||
|
|
#ifdef AVR32_PM_410_H_INCLUDED
|
||
|
|
const scif_pll_opt_t opt = {
|
||
|
|
.osc = SCIF_OSC0, // Sel Osc0 or Osc1
|
||
|
|
.lockcount = 16, // lockcount in main clock for the PLL wait lock
|
||
|
|
.div = 1, // DIV=1 in the formula
|
||
|
|
.mul = 5, // MUL=7 in the formula
|
||
|
|
.pll_div2 = 1, // pll_div2 Divide the PLL output frequency by 2 (this settings does not change the FVCO value)
|
||
|
|
.pll_wbwdisable = 0, //pll_wbwdisable 1 Disable the Wide-Bandith Mode (Wide-Bandwith mode allow a faster startup time and out-of-lock time). 0 to enable the Wide-Bandith Mode.
|
||
|
|
.pll_freq = 1, // Set to 1 for VCO frequency range 80-180MHz, set to 0 for VCO frequency range 160-240Mhz.
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Setup PLL1 on Osc0, mul=7 ,no divisor, lockcount=16, ie. 16Mhzx6 = 96MHz output */
|
||
|
|
scif_pll_setup(SCIF_PLL1, opt); // lockcount in main clock for the PLL wait lock
|
||
|
|
|
||
|
|
/* Enable PLL1 */
|
||
|
|
scif_pll_enable(SCIF_PLL1);
|
||
|
|
|
||
|
|
/* Wait for PLL1 locked */
|
||
|
|
scif_wait_for_pll_locked(SCIF_PLL1) ;
|
||
|
|
|
||
|
|
// Implementation for UC3C parts.
|
||
|
|
// Setup the generic clock for USB
|
||
|
|
scif_gc_setup(AVR32_SCIF_GCLK_USB,
|
||
|
|
SCIF_GCCTRL_PLL1,
|
||
|
|
AVR32_SCIF_GC_NO_DIV_CLOCK,
|
||
|
|
0);
|
||
|
|
// Now enable the generic clock
|
||
|
|
scif_gc_enable(AVR32_SCIF_GCLK_USB);
|
||
|
|
return PASS;
|
||
|
|
#else
|
||
|
|
return PCL_NOT_SUPPORTED;
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
#if UC3L
|
||
|
|
#else
|
||
|
|
void pcl_write_gplp(unsigned long gplp, unsigned long value)
|
||
|
|
{
|
||
|
|
#ifndef AVR32_PM_VERSION_RESETVALUE
|
||
|
|
// Implementation for UC3A, UC3A3, UC3B parts.
|
||
|
|
pm_write_gplp(&AVR32_PM,gplp,value);
|
||
|
|
#else
|
||
|
|
scif_write_gplp(gplp,value);
|
||
|
|
#endif
|
||
|
|
}
|
||
|
|
|
||
|
|
unsigned long pcl_read_gplp(unsigned long gplp)
|
||
|
|
{
|
||
|
|
#ifndef AVR32_PM_VERSION_RESETVALUE
|
||
|
|
// Implementation for UC3A, UC3A3, UC3B parts.
|
||
|
|
return pm_read_gplp(&AVR32_PM,gplp);
|
||
|
|
#else
|
||
|
|
return scif_read_gplp(gplp);
|
||
|
|
#endif
|
||
|
|
}
|
||
|
|
#endif
|